ارسال فایل فشرده مدارات لامپی

با درود و سلام و تبریک ایام

دوست گرامی مهندس سجاد گلچین پور فایلهای زیر را تهیه کردند که برای علاقمندان ارسال می گردد

http://s9.picofile.com/file/8268344418/4_830178914453160005.pdf.html

http://s8.picofile.com/file/8268344434/4_830178914453160006.pdf.html

عنوان  مطالب  مدارات لامپی است و چندین نمونه گیرنده و فرستنده  را ارایه نموده اند

طرح های لامپی = گیرنده موج خیلی بلند-فرستنده آ ام لامپی - فرستنده اف ام لامپی -سوار بر امواج رادیو -فرستنده اف ام - فرستنده تلگراف - مبدل موج کوتاه -فرستنده و گیرنده نوری -

CW-SSB-transceiver direct conversion to 10 meters

http://www.diagram.com.ua/list/rst-kb0.shtml

For SSB transceiver and CW transmitting and receiving in the range 28 ... 29.7 MHz. The device is built by direct conversion circuit with a common mixer - a modulator for receiving and for transmitting.

Specifications transceivers:

1. The sensitivity in reception mode for the signal / noise ratio of 10 dB, not worse ........ 1 mV.
2. The dynamic range of the receiving path, as measured by the method dvuhsignapnomu about .... 80 dB
3. Receiving channel bandwidth at -3 dB .................................... 2700Gts.
4. Bandwidth unipolar radiation transmission ....................... 2700 Hz
5. The carrier frequency and the non-operating side band suppressed not worse than ............................. 40 dB
6. The transmitter output power in CW on 750m load ............................... 7 W
7. Disposed frequency oscillator 30 minutes after the warm-up not exceeding ........ 200 Hz / hr.

Schematic diagram of the transceiver (without telegraph node) is shown in Figure 1. The transceiver has separate receiving and for transmitting high-frequency and low-frequency paths common to both modes is the mixer-oscillator and modulator VFO

Fig.1

Variable Frequency Generator (GPA) is made of two field-effect transistors and VT5 VT6 connection with a source driver. It operates at a frequency equal to half the frequency of the received or transmitted signal. When working at the reception and the transmission of the output circuits of the GPA is not switched, and does not change the load on the GPA. As a result, the transition from reception to transmission or vice versa, the frequency of the GPA is not rejected. Setting is made within a range by means of alternating air dielectric capacitor C10, which is part of the VFO loop. The SSB transmit mode, the microphone signal is amplified by the operational amplifier A2 and fed on to faeovraschatel elements L10, L11, C13, C14, R6, R7, which in the frequency range 300 ... 3000 Hz provides a phase shift of 90 °. The circuit L4 C5 serving total load mixers diodes VD1-VD8, allocated signal in the upper sideband range 28-29,7 MHz. High broadband faeovraschatel L8 R5 C9 in this range provides a phase shift of 90 °. Dedicated single-sideband signal through a capacitor C6 is supplied to a three-stage power amplifier transistors VT7-VT9.

Cascade pre-amplification and isolation of the mixer-modulator output circuit is formed on the transistor VT9. The high input resistance combined with low capacitance C6 provides a minimal impact on the power amplifier circuit.

In VT9 collector circuit switched circuit tuned at mid-range. The intermediate stage FET VT8 works in Class mode, "B", and the output stage in Class mode "C".

"U" -shaped low-pass filter on the L12 C25 and C26 clears the output signal from the high-frequency harmonics and ensures coordination of the output impedance of the output stage with impedance of the antenna. PA1 ammeter is used to measure current output transistor drain and indicates the correct settings "P" -filter.

Wire mode is provided by replacing the A2 amplifier sine wave oscillator frequency of 600 Hz (see Figure 2). Switching CW-SSB is done with S1. Telegraph key controls displacement VT11 preamp generator, and thus feed the low-frequency signal to the modulator.

CW-SSB-transceiver direct conversion to 10 meters

In receive mode, the power of the transmitter 42 on the stage is not supplied and the power amplifier and microphone amplifier are disabled. At this time, 12V voltage is applied to the cascade receive path.

The signal from the antenna is supplied to the input circuit L1 L2 C3 through the coupling coil, she agreed with the resistance of the circuit impedance of the antenna. On VT1 transistor RF amplifier made. The gain stage is determined by the bias voltage at its second gate (divider resistors R1 and R2). The load stage is L4C5 circuit connection RF amplifier stage with this circuit is carried out by means of the coil L3 Communications. With regard coil L5 signal is sent to a demodulator diode diodes VD1-VD8. The coils L8, L9 and L10 and the phase shifter is isolated L11 AF signal in the frequency band 300 ... 3000 Hz, which, via a capacitor C15 to the input of the operational amplifier A1. Strengthening of this circuit is determined by the sensitivity of the main transceiver in receive mode. The following AF amplifier transistor VT2-VT4, whose output signal is sent to the AF compact speaker volume B1 reception is controlled by the variable resistor R15.

In order to avoid loud clicks when switching modes "RX-TX" on UMZCH power transistor VT2-VT4 is served both in reception and transmission.

Most of the details of the transceiver is mounted on three printed circuit boards, pictures of which are shown in Figures 3-5. In the first board arranged the details of the input RF amplifier receiving channel (transistor VT1), the mixer parts - fazovraschayuschimi modulator circuits, as well as details of the local oscillator. The second board - low-frequency cascades on chips A1 and A2 and transistor VT2-VT4. on the third board amplifier power transmission path is placed. The board with mixer-modulator, RF amplifier and the GPA is screened.

Chassis transceiver has a width of 350 mm and a depth of 310 mm. On the front cover removed all controls and sockets for microphone and telegraph key. The speaker is also installed on the front panel, it is screwed M3 screws through the rubber grommets Mode Switching "RX-TX" is made pedal that -Includes disables voltage 42 V and operates two electromagnetic relays, one of which switches the antenna and the second voltage is 12 V at the receiving tract. Relay coil voltage feed 42, and de-energized include reception mode (RX).

Sockets for connecting the antenna, the pedals and the source 12 are located on the rear panel.

For the transceiver power used by the base stationary power supply unit, which supplies a constant stabilized voltage of 12 V with a current of 200 mA and a constant voltage of 42 V unstabilized with currents up to 1 A.

The transceiver used fixed resistors MLT on the power indicated in the diagrams.

Trimmer SDR-4a. Contour Ceramic capacitors necessarily, Trimmers CPC-M. Electrolytic capacitors K50-35 type or similar import. Variable capacitors oscillator and output circuits - with air dielectric.

For the winding contour coils RF amplifier, mixer and the transmitter using ceramic scaffolds 9 mm with cores trimmers SCR-1 (can be plastic frames from the paths UPCHI old tube TVs, but their thermal stability is much worse than that of the ceramic). Low-frequency coil mixer -modulyatora L8 and L9 are wound on the ring core of ferrite K16h8hb 100NN or more high-frequency (100VCH, 50VCH). The coils L10 and L11 are wound on the carcasses of the OB-30 2000IM1 ferrite. On these cores wound coil generators and erase bias semiconductor reel tape recorders.

Transistors KP303G KP303 can be replaced with any letter index or KP302. The transistor can be replaced by KP350A KP350B, KP350V or KP306. The transistor KP325 - by KT3102. Powerful FETs KP901 and KP902 can be any letter indices. For UMZCH fit any silicon and germanium (respectively) transistors corresponding structure. KD503 diodes can be replaced by KD514, adiod D9 to D18.

Establishing transceiver begin with GPA By adjusting core L7 and the inclusion of additional capacitor (5-30 pF) in parallel C10 generator is necessary to achieve the overlap in frequency 14.0 ... 14.85 MHz.

Table 1

CW-SSB-transceiver direct conversion to 10 meters

The work of the local oscillator can be checked using the RF frequency and RF voltmeter the voltage at each of the L6 coil halves should be 1.6 ... 1.8 V. If it is not included in these limits - you need to choose the number of coils L6. Now you need to go to the setup microphone amplifier and mixer - modulator. Do not connect the power 42 to apply 12V voltage at the output 7 A2 and test the functionality of the amplifier. Adjust the sensitivity can be the selection of the nominal value R31.

To set the mixer - the modulator need an oscilloscope, millivolt and tone generator (GZCH). With millivoltmeter and adjust the generator L11 contour C 14 on the frequency of 480 Hz, then loop L10 C13 on the frequency of 1880 Hz. Log phase shifter is disconnected from the capacitor C1S and C41, and the outputs from the L8 and L9 coils. Sign "X" and the oscilloscope AF generator output is connected to a connection point L10 and L11 coils. By the oscilloscope input "V connect SI L10 junction with the generator signal is fed to a frequency of 480 Hz In the oscilloscope display should be straight line sloping If instead the ellipse -... You need to fine tune the loop L11 S14.Zatem to input" Y "connected connection point L11 C12 and, in the same way check setting L10 C13 to the frequency of 1880 Hz. Thereafter, to the input of the oscilloscope "X" instead of the input of the phase shifter are connected free of its output. The channels of the oscilloscope sets the same gain. GZCH tuned to the frequency of 1880 Hz. The resistors R6 and R7 temporarily replace variable to 1 kW. Turn the R6 engine to achieve the appearance of the screen circumference. Then, setting GZCH 480 Hz is chosen in the same way the resistance of the resistor R7.

The setting is correct if the frequency change of the output GZCH in the range of 300 ... 3000 Hz on the oscilloscope screen, a circle will continue.

Resistor R5 achieve the best possible suppression of the lower sideband.

input circuit setting and L4C5 circuit to produce high frequency range. Then, sequentially energizing the power amplifier stages set up in the middle of the circuits L16 and L15 C34 C32 range. Setting the output stage is performed in the equivalent antenna connected - resistor 75 Ohm 10 W (you can solder the battery of four parallel connected resistors 2W 300 Ohm each).

Setting UMZCH comes to setting the selection of resistor R16 to the emitter voltage VT3 and VT4 equal to half the supply voltage.

Author: Bortko B .; Publication: N. Bolshakov, rf.atnn.ru

سایت دانلود رایگان

با سلام

 ادرس ذیل سایت بسیار مناسب رایگان جهت در یافت نقشه و اطلاعات اکثر وسایل الکترونیکی منجمله فرستنده گیرنده ها و مجلات و کتب می باشد

http://www.diagram.com.ua/english/library/funkamateur-magazine/funkamateur-magazine.php?row=1

http://www.diagram.com.ua/library/elektronika-usiliteli/elektronika-usiliteli.php?row=1

http://www.diagram.com.ua/english/library/handbooks-rcomp-motorola/

اعیاد

با سلام و تبریک ایام با سعادت  اعیاد قربان و غدیر و فرارسیدن مهرگان و جشن باستانی ایرانیان و ارزوی سلامتی  و موفقیت برای همه عزیزان

دارندگان پروانه بهره برداری از سرویس رادیو آماتوری

radio forty

با سلام و تبریک ایام

در دنیای رادیو اماتوری رادیوی 7 مگا یا کیت  فورتی بسیار مشهور بوده و اغلب  اماتورها دستی بر آن دارند

در ذیل چند عکس نمونه ازین رادیو  اراعه می شود

 مطلب فوق توسط مهندس ناصر فرشچی در گروه تلگرام بیان گردیده است با تشکر و کسب اجازه از محضر ایشان

http://lpistor.chez-alice.fr/fortyalbum.htm

27 mhz simple radio

سلام روزتان بشادی

طرحی از رادیوی 27  مگا  توسط مهندس  علیرضا سیفی   ترجمه و در گروه رادیو اماتوری اراعه گردید که بدلیل سادگی  تقدیم دوستان می گردد در صورت  علاقه سوال یا توضیح یا راهنمایی اگر لازم بود اماده پاسخ گویی   توسط اعضای محترم گروه و استادان 27 مگا یا بقول دوستان فرکانس مهندس عاملی هستم

ephamshop new products

با سلام  و آرزوی سلامتی و موفقیت دوستان

جناب مهندس قنبری دوست عزیز  و گرامی  ار شرکت    ephamshop  محصولات  زیر را  اراعه  نموده اند  که  در راستای  تولید ملی افتخار  ملی  بهترین  هستند

با عرض سلام خدمت دوستان عزيز :
ليست اقلام جديد موجود به شرح زير بهمراه قيمت آنها ارايه ميشود و دوستاني كه علاقمند به تهيه آنها ميباشند ميتوانند با ما به آدرس ايميل ephamshop@yahoo.com   تماس بگيرند .

فركانسمتر آماده با سون سگمنت تا 50 مگاهرتز 35000 تومان

 فركانسمتر مونتاژ و تنظيم شده قابليت اندازه گيري فركانس تا 1000 مگاهرتز85000 تومان

كيت آماده dds با قابليتهاي زير 240000 تومان


o  Supports 0~45MHz continual  adjust at 1Hz step.
o  Input 12V (Seller's Note: We  are also providing a simplified version, with input 8~9V)
o  With direct digital input  frequency
o  With audio volume potentiometer
o  With amp. gain potentiometer
o  With AGC potentiometer
o  S-LED display
o  Standing Wave-LED display
 
Keys & Connection interfaces:
•  ENC: encoder switch
•  MEM: switch for memory mode
•  VFO: Transfer from VFO A to VFO B, or from VFO B to VFO A.
•  SSB: Working mode change: circulate from USB, LSB, AM, CW, and on and  on...
•  RIT: fine tuning to receiving frequency
•  CAL: set functions
•  KB-1 and KB-2 have common shared pin, but is not GND.

 0

 
كيت آماده dds با قابليتهاي زير 240000 تومان

كيت مونتاژ شده ژنراتور با مشخصات زير295000 تومان :

ALI RADIOMAN, [۰۱.۰۸.۱۶ ۰۵:۱۶]
[Forwarded from ALI RADIOMAN]
The main operating modes:
Fixed-frequency mode (CW)
Sweep mode (SWEEP)
Servo signal patterns (SERVO)

Specifications:
The Output Signal Types: Sine, Square, Triangle, Positive and Negative Sawtooth, Positive and Negative Staircase, User-defined Arbitrary Waveforms, and Servo Control Signal
Frequency Range: 0-200KHz (Sine)
Frequency Resolution: 1Hz
Frequency Accuracy: 0.149Hz (when F> 40Hz), 0.000596Hz (when F <= 40Hz)
Cycle Resolution: 1ms
Amplitude Range: 0-10V pp
Amplitude Accuracy: 0.1V
DC Offset Range: -5V to +5V
DC Offset Accuracy: 40mV
Waveform Memory Depth: 256 Bytes
Maximum Sample Rate: 2.5Msps
Trigger Input Level: High 3.5V (Min.), low 1.5V (Max.)
When the Trigger Waveform Output Delay: Less than 5us
Synchronous Output: TTL Level
Output Impedance: 50 ohm
Power Supply Voltage: 15V DC
Supply Current: PCB Board Size: 15.5 * 5.5cm / 6.1 * 2.16in (L * W)
PCB Board Weight: 32g / 1.14oz
Screen Size: 6.5 * 1.5cm / 2.6 * 0.6in (L * W)
Screen Board Weight: 31g / 1.09oz
Panel Size: 15.5 * 6cm / 6.1 * 2.36in (L * W)
Package Size: 24 * 10 * 4.5cm / 9.45 * 3.94 * 1.77in
Package Weight: 194g / 6.85oz

Package List:
1 * DDS Digital Synthesis Function Generator Kit with Panel
1 * User Manual (English)

 

كيت فانكشن ژنراتور با مشخصات زير75000 تومان

Main AVR DDS V2.0 signal generator features:
Simple circuit ;
Dedicated high speed (HS) signal output up to 8MHz;
DDS signal with variable amplitude and offset;
DDS signals: sine, square, saw, rev saw, triangle, ECG and noise.
2×16 LCD menu;
Intuitive 5 button keypad.
Frequency adjusting steps: 1, 10, 100, 1000, 10000Hz;
Restoring last configuration after power up.

 

سينتي سايزر براي كسانيكه دستگاه كريستالي با تعداد كانال محدود و يا VCO دارند و ميخواهند قابليتهاي جديدي به آن اضافه نمايند با قابليت كنترل فركانس از 8 الي 164 مگاهرتز و در كانال UHF از 328/200 الي 491/500 كه محدوده آن ميتواند انتخاب شود و استپ فركانسي آن ميتواند از 2/5 كيلوهرتز الي 600 كيلوهرتز با مضربي از 2/5 كيلوهرتز انتخاب گردد موجود ميباشد . اين كيت داراي دو ولوم براي صدا و مدار سكوت است كه ميتواند بجاي دو ولوم در دستگاه شما عمل نمايد همينطور داراي ورودي براي نشان دادن شدت سيگنال  ورودي از تيونر دستگاه شما ميباشد و نيز داراي 39 حافظه است .

 
قيمت آن نيز 190000 تومان ميباشد

داراي سوييچ براي TX با اختلاف 10/7 مگاهرتز و نيز خروجي هدفون و كليد روشن و خاموش ميباشد

همچنين داراي كنترل اسكن فركانسي و قابليت تعيين محدوده اسكن ميباشد


گيرنده SDR داخل جعبه و مجهز به فن خنك كننده و فيش رابط USB و داراي چيپ RTL   170000 تومان

N]

كيت آماده dds با قابليتهاي زير 240000 تومان

قيمت آن نيز 190000 تومان ميباشد

دريافت از 30 الي 1400 مگاهرتز

اخرین لیست اسامی رادیو اماتورهای ایرانی

با سلام و آرزوی سلامتی و موفقیت دوستان عزیز

آخرین لیست اسامی رادیو آماتورهای ایرانی تقدیم می گردد

hommade radio

با سلام و تبریک ایام ولادت با خیر و برکت امام مهربانی ها امام رضا علیه السلام

دوست عزیزم  مهندس دل قوی رادیوئی  تک باند با استفاده از اسیلاتور اردینو و دی دی اس 9850 و برد مولتی اس اس بی جناب قنبری و تقویت کننده پوش پول ایشون ساختند و در تست هم تماس های خیلی عالی با کشورهای مختلف داشتند عکس و نقشه های رادیوی ایشون بشرج زیر است